The Wireless Containment System unit can last up to approximately 10 years or more if used properly. Batteries on the collar can last and be replaced up to 1 to 2 months.
How do I know if my PetSafe collar is working?
All you have to do is hold the tool against the contact points on your dog or cat’s receiver collar to check if the collar is working properly. The test light tool will light up if static correction is being activated. This accessory comes in most kits including a fence receiver collar, remote trainer, or bark collar.
Can you replace the collar on a PetSafe collar?
Replacement 3/4-inch or 1-inch strap for PetSafe in-ground and wireless fence receiver collars. Simply remove the receiver unit from your pet’s old receiver collar and place it on the new collar strap.
Why is my PetSafe collar beeping but not shocking?
Touch both points on the collar while it is ticking or beeping. If you do not feel a shock, then there may be a problem with the receiver collar. Make sure you touch both points on the receiver at the same time when you hear the collar beeping. It will tell you definitively that the fence is or is not working.
How long does PetSafe battery last?
Keep all of your pet’s essential electronics working their best with PetSafe RFA-67 6 Volt Replacement Batteries. The 2-count pack of 6 volt batteries can provide up to 6 months of power (each battery can last 1-3 months with proper use). The patented design makes them easy to install and use.
Does PetSafe collar turn off?
The Safety Shut Off feature automatically turns the collar off for three minutes if your dog barks more than 15 times within an 80 second period. CRefrain from having your dog wear the collar longer than 12 hours to avoid skin irritation. Water resistant, not submersible. Intended for dogs six months or older.
Why is my PetSafe collar not working?
If Receiver Collar does not beep and the Test Light does not flash, replace the 10. battery in the Receiver Collar. If it still does not beep and the Test Light does not flash, contact the Customer Care Center at 1-800-732-2677. If the Receiver Collar beeps, there may be a complete or partial break in the 11.
Why is my Invisible Fence collar blinking red? If you have started to see a red flashing light on your pet’s Computer Collar unit, your Power Cap battery may need to be replaced. You can order replacement batteries online, from your local dealer, or by calling 1-800-824-3647.
How long can you keep a bark collar on a dog?
Before playing with your dog, remove the Bark Control Collar. The activity may cause your dog to bark, which could lead to him associating the play with the Static Correction. Never leave the Bark Control Collar on for more than 12 consecutive hours.
How do you remove a petsafe collar?
This collar is designed to tighten with the pulling strength of your pet and once there is no more pull it will automatically loosen. To remove the collar simply slip it over you pets head and ears.
How do I change the correction level on my petsafe collar?
How do I remove the battery from my petsafe stay and play collar?
Why does my petsafe collar beep randomly?
Please restart the collar by simply by taking out the battery than put it back. Try to use the collar on low sensitivity setting first then change the sensitivity according to the dog’s barking. If still you see the continuous beeping, please put a new battery.
What does it mean when a petsafe collar beeps?
If the collar beeps or the test light tool illuminates, the battery and collar are working. If not, replace the battery.
Why is my petsafe collar beeping in the house?
If your house is very big and if the containment area has a relatively small radius, it’s likely that a part of the containment boundary falls somewhere inside your house, causing the collar to beep whenever it crosses that part of the boundary.
How long should a dog collar battery last?
Most recommend that invisible fence batteries be replaced every 3 months to ensure that your dog will be continually protected and contained within the fencing. It’s better to be safe than sorry. You don’t want to find out the hard way that the battery inside your dog’s collar has failed!
How long does a dog collar battery last?
During normal training use, these training collar batteries frequently last between 6 months and a year. When the battery level gets too low, it can simply be replaced with any standard 9-volt battery.
How long does it take to charge PetSafe collar?
Step 1: Charge the Receiver Collar
The collar light is red while charging and green when fully charged. The first charge will take about 2 or 3 hours. Each charge can last up to 3 months depending on the frequency of use.
How does PetSafe collar work?
When the vibration of your dog’s bark triggers the Sensor Probe, a static correction is administered through the Contact Points. The Bark Control Collar starts with the lowest level of static correction and then increases through 6 levels each time your dog barks within 30 seconds of the previous bark.
How do you test the PetSafe rechargeable bark control collar?
- Press and release the power button to power the collar on.
- Watch for the green light to blink twice, then hold the power button. Continue to hold the power button through the red light.
- Release the button when the light turns blue to set the collar into test mode.
How do you reset a stubborn dog collar?
To reset the low battery indicator, remove the battery from the Receiver Collar. Discharge all power by holding the correction level button down until the light is no longer illuminated. Reinstall battery.
How do you pair a new PetSafe collar?
Turn the collar off prior to pairing. Confirm it is turned off by checking that the light is not flashing. Press and hold the power button on your second collar for five seconds. The light will turn solid green, then begin to flash and beep.
How do I increase the shock on my PetSafe collar?
Increase the Static Correction Level by pressing and releasing the Correction Level Button within 5 seconds of the previous flashes. The Static Correction Levels increase from 1 to 5. Pushing the Correction Level Button while the Receiver Collar is on level 5 will cause the Receiver Collar to revert to level 1.